Plans

Free DIY Furniture Plans to Build an Original Office Large Hutch

12.09.13 By //
Project Image

Free DIY Furniture Plans to Build an Original Office Large Hutch. There are only a few pieces left before we finish out the Original Office Collection, and you guys will be able to customize till you drop! I can’t wait to see how you mix and match to arrange your own pieces! Xx… Rayan

Estimated Cost

$75-$100

Dimensions
Dimensions for This Project
Tools
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Countersink Bit for Drill
  • Square
  • Sander
  • Kreg Jig
  • Brad nailer
Lumber
  • 2 – 1×2 at 8’
  • 2 full sheets of ¾” plywood
Materials
  • 1-1/4” pocket hole screws
  • 1-1/4” screws
  • 1-1/4” brad nails
  • Edge banding for the plywood edges, optional
  • Wood filler
  • Sandpaper
  • Wood glue
  • Finishing Supplies
Cut List
  •  2 – 1×2 at 11-1/4” – Feet
  • 2 – ¾” plywood at 11-1/4” x 43-1/2” – Sides
  • 1 – ¾” plywood at 11-1/4” x 73-1/2” – Bottom
  • 1 – ¾” plywood at 40-3/4” x 73-1/2” – Back
  • 1 – ¾” plywood at 10-1/2” x 73-1/2” – Long Shelf
  • 1 – ¾” plywood at 10-1/2” x 28-3/4” – Divider
  • 2 – 1×2 at 36-3/8” – Stretchers
  • 2 – ¾” plywood at 10-1/2” x 36-3/8” – Shelves
  • 1 – ¾” plywood at 12-1/4” x 77” – Top
  • 2 – 1×2 at 11-1/4” – Side Trim
  • 1 – 1×2 at 76-1/2” – Front Trim
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1
Step 1

If using edge banding, it will be applied to the exposed edges of the plywood before assembly.

Cut the pieces for the sides and feet. Set the Kreg jig for ¾” material and drill pocket holes in the top edge of each side. Attach the feet to the bottom using glue and countersunk 1-1/4” screws. The side pieces will be positioned at the center of each foot.

Step 2
Step 2

 Cut the piece for the bottom and drill pocket holes in each end. Position as shown then secure using glue and 1-1/4” pocket hole screws.

Step 3
Step 3

Cut the piece for the back and drill pocket holes in all four edges. Position as shown then secure using glue and 1-1/4” pocket hole screws.

Step 4
Step 4

Cut the piece for the long shelf and drill pocket holes in each end as well as one long edge. Position as shown then secure using glue and 1-1/4” pocket hole screws.

Step 5
Step 5

Cut the piece for the divider and drill pocket holes in each end as well as one long edge. Position as shown and secure using glue and 1-1/4” pocket hole screws.

Step 6
Step 6

Cut the pieces for the shelves and drill pocket holes in each end as well as one long edge. Position as shown then secure using glue and 1-1/4” pocket hole screws.

Cut the piece for the stretchers and drill pocket holes in each end. Position as shown then secure using glue and 1-1/4” pocket hole screws. The outside face of the stretcher will be flush with the outside edge of the sides.

Step 7
Step 7

 Cut the piece for the top. The front and sides will overlap by 1”. Secure using glue and 1-1/4” pocket hole screws through the holes drilled in the sides and back.

Step 8
Step 8

Cut the pieces for the trim. Rout a decorative edge along one long edge of each piece if desired. Position the sides first and secure with glue and 1-1/4” brad nails, then attach the front in the same manner. A mitered corner will be used if routing a decorative edge. Adjust the length of the sides accordingly. Store-bought trim can also be used.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

Print Friendly, PDF & Email

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.