Plans

Free DIY Furniture Plans // How to Build a Rocking Chair

04.13.15 By //
The Design Confidential Free DIY Furniture Plans How to Build a Rocking Chair

Nothing says spring like a rocking chair on the porch. I kind of have a thing with chairs that rock… or bounce. I guess I never grew out of that stage from my years as a baby? Who knows, but there is definitely something so soothing about sitting in a rocking chair, listening to the evening sounds. It is even better in the morning, but somehow school routines and young children seem to keep this from happening during the week. A gal can dream though…

As with all of our plans, you are building at your own risk and you should have a firm understanding of building in general before you attempt many of our plans (some are easy as pie and perfect for beginners). With that, go forth, have fun, take lots of pictures and share them in a showcase on the site or on social media with the hashtag #builtTDCtuff and we will share our faves! Be sure to tag @thedesignconfidential on Instagram / FB and @thedesconf on Twitter / Pinterest. If you are a blogger and you post about your build, don’t forget to include a link to your post on your showcase here. Don’t forget… for all of our newer plans, clicking on the images will let them expand to enormous sizes with much greater clarity. The older plans may need updating so please let us know if you need one fixed!

$50-$100
The Design Confidential Free DIY Furniture Plans How to Build a Rocking Chair
  • 2 – 1×2 at 8’
  • 3 – 1×3 at 8’
  • 2 – 1×4 at 8’
  • 1 – 1×6 at 8’ (or use 3/4” plywood, ripped down to 5-1/2” wide)
  • 1 – 1×2 at 16” – Backrest Top Frame
  • 2 – 1×2 at 18-1/2” – Backrest Side Frames
  • 2 – 1×3 at 2-1/2” – Armrest Supports
  • 2 – 1×3 at 21” – Backrest Sides
  • 5 – 1×4 at 19” – Backrest Slats
  • 2 – 1×3 at 23” – Seat Sides
  • 2 – 1×2 at 17-1/2” – Seat Front and Seat Back
  • 5 – 1×4 at 19” – Seat Slats
  • 2 – 1×3 at 22” – Armrests
  • 2 – 1×3 at 12-1/4” – Side Frame Tops
  • 4 – 1×3 at 24-1/2” – Side Frame Sides
  • 2 – 1×2 at 19-1/2” – Side Frame Bottoms
  • 2 – 1×6 at 35” – Rockers

Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

/ Click on Images to Enlarge

Cut the pieces for the Backrest Top Frame and Backrest Side Frames. With the Kreg jig set for 3/4” material, drill pocket holes in each end of the Backrest Top Frame. Assemble as shown with glue and 1-1/4” pocket screws.

Cut the pieces for the Armrest Supports, Backrest Sides, and Backrest Slats.

Cut the Armrest Supports as shown.

Chamfer the top back corner of the Backrest Sides at a 45-degree angle, if desired. You can also “round out” the bottoms of the Backrest Sides as shown. Attach the Backrest Sides to the Backrest Side Frame pieces as shown with glue and 1-1/4” wood screws. Attach the Armrest Supports to the Backrest Sides as shown with glue and 1-1/4” wood screws.

Attach the Backrest Slats to the Backrest Top Frame and Backrest Sides as shown with glue and 1-1/4” wood screws.

Cut the pieces for the Seat Sides, Seat Front, and Seat Back. Chamfer the bottom front corner of the Seat Sides at a 45-degree angle, if desired.

With the Kreg jig set for 3/4” material, drill pocket holes in each end of the Seat Front and Seat Back. Assemble as shown with glue and 1-1/4” pocket screws.

Cut the pieces for the Seat Slats. Attach the Seat Slats to the Seat Front, Seat Sides, and Seat Back as shown with glue and 1-1/4” wood screws.

Cut the pieces for the Armrests, Side Frame Tops, Side Frame Sides, and Side Frame Bottoms. You can “round out” the outer corners of the Side Frame Sides as noted to allow for better chair movement. With the Kreg jig set for 3/4” material, drill pocket holes in each end of the Side Frame Tops and Side Frame Bottoms. Next, drill pocket holes in the top end of the Side Frame Sides. Assemble as shown with glue and 1-1/4” pocket screws. Repeat this step for the other side.

Cut the pieces for the Rockers. Draw out the shape as shown and cut out with your jigsaw. Make sure you draw a gentle curve. For this project, we used a radius of 62-1/2” for the Rocker curves. If desired, “round out” the end corners of the Rockers with your jigsaw or sander.

Clamp the Rockers to the Side Frame Sides as shown. Using a 1/4” spade bit, drill holes through both of the clamped pieces. Attach the Rockers to the Side Frames Sides as shown with glue and 1/4” bolts and nuts. Once assembled, you can see what part of the Side Frame Sides extend past the Rockers. Use your jigsaw or sander to remove this excess wood. Repeat this process with the other side.

Lay one of the Side Frame assemblies on the ground or table, with the pocket holes facing up. Lay the Seat assembly on the Side Frame assembly as shown and secure with clamps. Using a 1/4” spade bit, drill holes through both of the clamped pieces. Attach the Side Frame Sides to the Seat Side as shown with glue and 1/4” bolts and nuts. Repeat this process with the second Side Frame assembly.

Set the Rocking Chair upright. Using clamps, position the Backrest assembly to the Side Frame assemblies as shown. The bottom corner of the Armrest should be flush with the back edge of the Backrest Side and should be set directly on the Armrest Support. Use your 1/4” spade bit to drill through both the clamped pieces where noted. Attach the Side Frame Sides to the Backrest Side as shown with glue and 1/4” bolts and nuts. Repeat this process with the other side.

Just sit back, relax, and rock your worries away!

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

// Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you ONLY use 1 image and provide an ADEQUATE link back to the original source and appropriate plan! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential. By accessing or using any part of the web site, you agree to become bound by the terms and conditions of this website as outlined under Terms of Use. If you do not agree to all the terms and conditions of this agreement, then you may not access the Website or use any services. The information contained in this website is for general information purposes only. The information is provided by The Design Confidential.com and while we endeavor to keep the information up to date and correct, we make no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability or availability with respect to the website or the information, products, services, or related graphics contained on the website for any purpose. Any reliance you place on such information is therefore strictly at your own risk. In no event will we be liable for any loss or damage including without limitation, indirect or consequential loss or damage, personal injury or death, or any loss or damage whatsoever arising from loss of information or profits arising out of, or in connection with, the use of this website. I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it. The Design Confidential.com is inspired by but does not replicate exact designs, any similarities between these plans and items sold at specialty retailers is coincidential and not endorsed by or related to any said retailers. // Post May Contain Affiliate Links

Print Friendly, PDF & Email

4 comments on “Free DIY Furniture Plans // How to Build a Rocking Chair”

  1. I make outdoor furniture from cypress and aromatic cedar. I have been asked to build rockers that imitate my chair design(modified Adirondack ) legs 24″ on center, 3 1/2 width of legs and rear riser. Can you guys help me with my initial design? I will pay for design or templates. photos of my design can be sent/ thx

  2. We built this exactly per the plans and when you assemble at the end there’s basically nothing holding the top end of the backrest to the chair. It’s only attached at the bottom which means you sit down and the back pivots. Help?

    1. Yep, I can see how this might be. This was a plan that Cher drew up a while back, and I think she was thinking that the angle of the armrest support, in combination with the armrest, would keep things from pivoting. Let me think about how to solve for this… Off the top of my head I’m thinking that securing the armrest to the armrest support will help, but I’m not sure if that alone will be strong enough. Perhaps you can give this a try and see if it is enough or if we need more support to keep it from moving? Try securing the armrest to the support from the top, down into the support using a 1 1/4″ wood screw. If you are clever with your placement of this, and place it toward the front of the support, you might also be able to secure from underneath at an angle from the back of the support, up into the armrest. This second screw would need to be carefully placed as well so you don’t come out the top of the armrest with it.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.